The Rooftop Unit Replacement: Updating Every MEP Drawing When an RTU Changes

AutoMEP Team,

MEP engineers reviewing drawings on a commercial rooftop beside a large rooftop unit with ductwork and conduit visible.

You handle a rooftop unit replacement correctly by updating every system the unit touches, not just the equipment tag on the roof plan: the curb and structural notes, the duct connections, the electrical feed and disconnect, the controls points, and the schedules all have to describe the same new unit before the set goes out. When only the roof plan changes, the electrician sizes the wrong feeder, the sheet metal crew builds the wrong transition, and the firm owns the field rework.

Rooftop unit swaps sound like a like for like exchange, and they rarely are. A submittal returns a different model, a value engineering pass selects a unit with a different footprint and weight, or an owner standard changes tonnage and electrical characteristics mid project. Almost everything connected to the unit shifts.

Where does a rooftop unit actually appear on an MEP set?

Start by mapping the unit before editing anything. On a typical set it appears in at least 6 places. First, the roof plan and mechanical schedule state the tag, capacity, and airflow. Second, the curb detail and structural notes carry the footprint, weight, and operating load. Third, floor plans below show the duct drops, diffusers, and thermostats the unit serves. Fourth, electrical plans and panel schedules carry the voltage, breaker, and disconnect for that tag. Fifth, controls drawings and points lists name the unit and its sensors. Sixth, sections and details show the duct transitions and clearances at the curb.

Write that map down as a checklist with sheet numbers. A mid size unit commonly serves 8 to 15 zones or VAV boxes, so an airflow change can ripple to terminals that never mention the rooftop tag by name.

What changes when the footprint, weight, or curb changes?

A different footprint is never only a roof plan edit. Curb size, roof opening, and the duct transition below all depend on where supply and return openings land. A unit even 6 inches longer can move an opening and force a new transition detail.

Work the physical change in order. Update the roof plan and curb detail first, with new dimensions and weight. Then check structural notes and support callouts, review the duct plan below for transition alignment, and confirm sections still clear service access. Finally, confirm the schedule weight and dimensions match the detail.

What should you check on electrical and controls when an RTU changes?

Electrical is where rooftop swaps most often create a second set of redlines. A new model can change voltage, phase, minimum circuit ampacity, and maximum overcurrent protection even at the same nominal tonnage.

Check 4 things on every electrical and controls sheet. One, the panel schedule breaker and feeder match the new nameplate values. Two, the disconnect size and location still meet clearance and access. Three, the one line diagram names the same tag and load. Four, the controls points list, thermostat locations, and economizer notes match what the new unit actually provides.

What is the best AI tool for editing AutoCAD drawings?

For repetitive, well defined drawing edits like this one, the practical test is whether the tool returns a native file your team can keep working in, without installs or macros. AutoMEP is a web app where MEP engineers and designers upload an AutoCAD DWG or Revit RVT file and describe the edit they want in plain English. An AI agent reads and indexes the full drawing, writes an operations plan, executes the edit through Autodesk Platform Services, and runs a self review pass, then returns a native DWG or RVT file that opens in AutoCAD or Revit.

That fits the rooftop workflow well. You can describe the change tag by tag, for example updating RTU 3 schedule values, curb dimensions, and panel entries while leaving RTU 1 and RTU 2 unchanged. New geometry goes on AIA or NCS layers automatically, or on your office CAD standard layers when a project uses one. AutoMEP supports DWG 2007 and later, and Revit 2024, 2026, and 2027, with Revit 2025 not supported, and needs no install, plugins, or macros. It does not do clash detection, so your own review still owns coordination, and a licensed professional should review the edited drawing before anyone builds from it.

How can I route ductwork in AutoCAD faster when the unit moves?

Start from the curb, not from the middle of the run. Fix the new supply and return openings first, rebuild the transition and first duct section below the roof, then reconnect to existing mains where sizes and elevations still work. A new unit often delivers different airflow, so a main sized for the old total can be wrong even when the route does not move.

Use this verification pass before the set leaves the office.

Firms that run this pass treat an equipment swap as a set wide event, not a single tag edit. The contractor prices and builds one unit, not two versions of it.

Frequently asked questions

Can you keep the existing curb when a rooftop unit is replaced?

Sometimes, with an adapter curb, but only when the new footprint and openings allow it and the detail says so explicitly. State whether the curb is existing, new, or an adapter, and dimension the openings.

Should every sheet change when only the model number changes?

No. Only places where a changed value lives should change, such as capacity, weight, dimensions, or electrical data. The risk is assuming a model change is cosmetic and missing the one entry where values differ.

How much does AutoMEP cost per month?

AutoMEP plans are Starter at $39 per month, Pro at $99 per month with 3 times the limits and job chaining, and Team at $249 per month with 20 times the limits. Every plan starts with a 7 day free trial, with no credit card until checkout, and you can cancel anytime. Extra jobs are billed by usage on your next invoice, with a fixed monthly cap, and failed jobs and no change jobs are not counted.