How do I write a good request for an electrical plan?
AutoMEP reads the rooms, doors and blocks already in your plan, so an electrical request works best when it says three things: which rooms, which symbol, and where in the room. Here's a request that does all three:
"In the rooms labeled VESTIAIRE, add four recessed 2x2 fixtures centered in the ceiling using block F2X2ENC2T, a switch beside the entry door using block SW on layer E-Devc-Ltg, and two receptacles along the walls, not under the window."
Name the rooms the way your plan does: "the rooms labeled VESTIAIRE", "every office", "each bedroom". AutoMEP finds the rooms by their labels, so the words on your plan work best, in any language.
Your own symbols: when your drawing already has a switch, receptacle, fixture or equipment block, AutoMEP inserts that block on your layer instead of drawing a new symbol. To choose one, name the block and the layer, for example "use block SHDXL on layer E-Devc-Pwr for the hand dryer". If the name you give isn't in the drawing, AutoMEP uses the closest block it has and tells you which one. If the drawing has nothing that fits, it draws the standard plan symbol, or a labeled box for unusual equipment, and says so.
Where it goes: say it the way you'd tell a drafter. "Beside the entry door, on the handle side", "along the walls, not under the window", "a fixture grid centered in the room", "on the wall behind the desk". Without a rule, switches go beside the door you walk in through, ceiling lights in the middle of the room and receptacles along the walls.
Circuits and panels: ask for the panel in the same sentence, for example "with a homerun to panel LP-1". For lights that are already drawn, "wire the lights to junction boxes, then the junction boxes to panel ADP". Each homerun gets its circuit tag. AutoMEP doesn't do load calculations, so check the circuits against your own numbers.
Counts: "add a bill of materials table for the electrical layers" lists the devices, including the blocks already in your drawing.
One request or several: on a trial or the Starter plan, each request starts again from your original upload, so put everything for one plan into a single request. On Pro and Team, with Build on the last result ticked, each request adds to the one before.
Checking the result: when AutoMEP used blocks from your drawing, the note on the finished job starts by naming them, and it goes on to list anything it substituted or assumed. Open the result in the viewer to check positions before you download it.
AutoCAD MEP and Architecture objects: new devices are standard AutoCAD blocks, not AutoCAD MEP smart devices, so they don't carry circuit data inside AutoCAD MEP. Walls, doors and windows drawn as AutoCAD Architecture objects are read as outlines, so say which side a door opens when it matters. More in what AutoMEP can't do yet.
"In the rooms labeled VESTIAIRE, add four recessed 2x2 fixtures centered in the ceiling using block F2X2ENC2T, a switch beside the entry door using block SW on layer E-Devc-Ltg, and two receptacles along the walls, not under the window."
Name the rooms the way your plan does: "the rooms labeled VESTIAIRE", "every office", "each bedroom". AutoMEP finds the rooms by their labels, so the words on your plan work best, in any language.
Your own symbols: when your drawing already has a switch, receptacle, fixture or equipment block, AutoMEP inserts that block on your layer instead of drawing a new symbol. To choose one, name the block and the layer, for example "use block SHDXL on layer E-Devc-Pwr for the hand dryer". If the name you give isn't in the drawing, AutoMEP uses the closest block it has and tells you which one. If the drawing has nothing that fits, it draws the standard plan symbol, or a labeled box for unusual equipment, and says so.
Where it goes: say it the way you'd tell a drafter. "Beside the entry door, on the handle side", "along the walls, not under the window", "a fixture grid centered in the room", "on the wall behind the desk". Without a rule, switches go beside the door you walk in through, ceiling lights in the middle of the room and receptacles along the walls.
Circuits and panels: ask for the panel in the same sentence, for example "with a homerun to panel LP-1". For lights that are already drawn, "wire the lights to junction boxes, then the junction boxes to panel ADP". Each homerun gets its circuit tag. AutoMEP doesn't do load calculations, so check the circuits against your own numbers.
Counts: "add a bill of materials table for the electrical layers" lists the devices, including the blocks already in your drawing.
One request or several: on a trial or the Starter plan, each request starts again from your original upload, so put everything for one plan into a single request. On Pro and Team, with Build on the last result ticked, each request adds to the one before.
Checking the result: when AutoMEP used blocks from your drawing, the note on the finished job starts by naming them, and it goes on to list anything it substituted or assumed. Open the result in the viewer to check positions before you download it.
AutoCAD MEP and Architecture objects: new devices are standard AutoCAD blocks, not AutoCAD MEP smart devices, so they don't carry circuit data inside AutoCAD MEP. Walls, doors and windows drawn as AutoCAD Architecture objects are read as outlines, so say which side a door opens when it matters. More in what AutoMEP can't do yet.
More in MEP Operations
Did this answer your question? If not, contact support and send us the drawing.