How do I write a good request for an HVAC plan?
Give AutoMEP three things: which rooms to serve, the airflow, and where the air comes from. Here's a request that does all three:
"Add supply and return ductwork from AHU-1 in the Mechanical room to the Kitchen, Dining and Living rooms, sized for 800 CFM supply and 800 CFM return, with one ceiling diffuser and one return grille in each room."
Give the airflow, not the size: AutoMEP picks each duct size from SMACNA tables, or from EN 1505 and EN 1506 on metric projects, and the finished job names the table it used. If you state a size, it draws that size. If you leave the airflow out, it picks a reasonable value and tells you what it assumed.
Name the source: an air handler, rooftop unit or fan already on the plan, by its tag or the room it's in. If the equipment is on another floor, say so, and AutoMEP marks where the duct leaves this plan instead of inventing a floor.
Diffusers, grilles and thermostats: ceiling diffusers and grilles go in the middle of each room you name, and thermostats go on a wall. Say how many you want per room, for example "two supply diffusers in the Exercise Room". If your drawing already has a diffuser or thermostat block, AutoMEP uses it.
Exhaust and piping: "exhaust ductwork from both restrooms to EF-1" goes on its own exhaust layer. Refrigerant and chilled water lines can be run the same way, each on its own layer. Every run is routed around walls and through door openings rather than straight across the plan.
Tags and schedules: new equipment is tagged with its name and airflow, for example "VAV-1 @ 800 CFM". Ask for a diffuser or VAV schedule beside the plan if you want one.
One request or several: on a trial or the Starter plan, each request starts again from your original upload, so put the whole layout in one request. On Pro and Team, with Build on the last result ticked, each request adds to the one before.
What it doesn't do: heating and cooling load calculations or energy models. Treat the layout as a starting point for your own numbers. More in what AutoMEP can't do yet.
"Add supply and return ductwork from AHU-1 in the Mechanical room to the Kitchen, Dining and Living rooms, sized for 800 CFM supply and 800 CFM return, with one ceiling diffuser and one return grille in each room."
Give the airflow, not the size: AutoMEP picks each duct size from SMACNA tables, or from EN 1505 and EN 1506 on metric projects, and the finished job names the table it used. If you state a size, it draws that size. If you leave the airflow out, it picks a reasonable value and tells you what it assumed.
Name the source: an air handler, rooftop unit or fan already on the plan, by its tag or the room it's in. If the equipment is on another floor, say so, and AutoMEP marks where the duct leaves this plan instead of inventing a floor.
Diffusers, grilles and thermostats: ceiling diffusers and grilles go in the middle of each room you name, and thermostats go on a wall. Say how many you want per room, for example "two supply diffusers in the Exercise Room". If your drawing already has a diffuser or thermostat block, AutoMEP uses it.
Exhaust and piping: "exhaust ductwork from both restrooms to EF-1" goes on its own exhaust layer. Refrigerant and chilled water lines can be run the same way, each on its own layer. Every run is routed around walls and through door openings rather than straight across the plan.
Tags and schedules: new equipment is tagged with its name and airflow, for example "VAV-1 @ 800 CFM". Ask for a diffuser or VAV schedule beside the plan if you want one.
One request or several: on a trial or the Starter plan, each request starts again from your original upload, so put the whole layout in one request. On Pro and Team, with Build on the last result ticked, each request adds to the one before.
What it doesn't do: heating and cooling load calculations or energy models. Treat the layout as a starting point for your own numbers. More in what AutoMEP can't do yet.
More in MEP Operations
Did this answer your question? If not, contact support and send us the drawing.